Description
Rolls Royce Phantom Mileage Blocker sometimes is mentioned as: Can Emulator – Can Blocker – Mileage Freezer – Odometer stopper – Odometer freezer – Stop KM – Can Filter – Kilometer Filtern – Tachojustierer – Tacho Stopper – Tacho Blocker – KM Stop Freezer – Stop Mileage – Turn Off Speedometer – How to Stop My Mileage – Turn Off Odometer – Mileage Correction
ROLLS ROYCE PHANTOM VIII (2017 – Present)
Order today Rolls Royce Mileage Blocker which is an extraordinary device which can stop the mileage recording on a vehicle you owe. Such a device is useful if you wish to stop counting unnecessary miles or kilometres while testing your car’s performance under different conditions. The main advantage of our mileage blocker is that it is 100% untraceable to people and sophisticated diagnostic equipment.
Key features of our KM Freezer:
- All modules in the vehicle will show the same mileage (odometer, transmission ecu, key fob etc) ✔️
- Instructions and WhatsApp support provided – remove the cluster, disconnect it and connect the Mileage Blocker ✔️
- Simple installation – doesn’t require cutting or soldering cables ✔️
- Original connectors and best quality workmanship ✔️
- After removal of the device mileage doesn’t jump up ✔️
- Always saves the last setting. The module does not need to be reactivated every time you start the car ✔️
This module works on cars with and without the firmware update! ⚠️
Functional sequence:
🔹 Mode 1 – shows correct driving speed and odometer is stopped (0% count) – works only on cars without 2019 software update
🔹 Mode 2 – shows 10% driving speed and odometer counts 10% (70mph = 7mph) – works with new software and Live Cockpit
🔹 Mode 3 – shows correct driving speed at all times and odometer is slowed down (counts around 30%) – works with new software
🔹 Mode 4 – shows correct driving speed at all times and odometer is slowed down (counts around 35%) – works with new software
🔹 Mode 5 – mileage freezer is turned off; 100% count and speed displayed as normal
Activation ✔️ deactivation ❌ and switching between modes anytime by pressing and holding of the BC button
In all modes cruise control, speed limiter and adaptive cruise control is working as normal.
🔹 Confirmation of activation takes place in the instrument cluster
🔹 Nothing needs resetting every time you start your journey – this Mileage Stopper always saves last working mode
🔹 Activation and deactivation can take place at any time, both while driving and while stationary
We offer a wide variety of odometer devices for various vehicles. The installation process of the Can Blocker is similar for most models and doesn’t require in-depth knowledge of vehicle’s maintenance. However if you wish to book in mileage blocker fitting service, please contact us directly
Worldwide shipping with DHL Express – we process domestic and international orders daily – ship to the whole of Europe, United States, Canada, New Zealand, Russia, Japan, Taiwan and all over the world
What is Can Blocker and Canbus anyway? Canbus is the spinal cord that connects many modules or computers throughout your Rolls Royce together and allows them to operate as a ‘cohesive’ team. Our devices include this same level of vehicle-wide computer integration as Electronic Control Units in your car. A Mileage Blocker with its Canbus connection can read virtually every set of data including critical internal calculations like fuel trims, driving speeds mileage data and change these values to suit your requirements.
For the mode that alters the mileage entirely, we allow a deviation of up to 1% of the driven distance. Provided details about stopped mileage are only approximations, and there might be such minor differences.
Our Mileage Blocker not only stops counting covered distance in all memories of a vehicle but also automatically corrects the service. The only part which isn’t stopped while using the tool is „Service“. It is still counted down but does not record any mileage until 30% remains. If there remains 30% before the due date, it automatically jumps back up to 90%. If it’s pushed back up to 90% from 30%, before a message was sent, then that service reset is not recorded.
Each service is counted down from the traveled distance time. The service interval for a vehicle is structured like this. As a rule, a service must be made in every 30,000 km for diesel and 15,000 for petrol. The service is counted down while driving. If you drove 1,000 km then the next service would be in 29,000 km. If you stop mileage, then the service shouldn’t count down, but it still continues working until it reaches 30%. In the case of 30,000km, the remaining 30% is equal to 9,000 km.
When the kilometre stopper is active, it automatically pushes the service back up to 90% i.e. to 27,000km. The abovementioned numbers are not 100% correct, because many engines have different service intervals, but the percentages are correct.
Change modes via smartphone app or press the BC button for 10 seconds
Repeat the process to switch from mode to mode
All percentages of the distance driven are approximate and not binding because they are influenced by the environment ( city/ traffic jam/ highway). And only after a longer distance of approx. 100 km / mi can you see what percentage was actually counted.
Mode 1
1. Vehicle till 2019 and without update and the live cockpit: Speed display works and the Mileage counting is stopped. 1. Vehicle: Speed = original, Counting miles approx 0-1%. Works only with models until 2019, without Update and the Live Cockpit.
Mode 2
No speed and the mileage counting is stopped for all vehicles
Mode 3
Speed display works and the miles count is reduced to 30%.
Interval count: stop 1 minute, count 15 seconds, repeat. 30 % is a guide value. The driving environment determines the count. Works independently of software updates for all vehicles until 2023. The indicator: Turn light x3 flashes only inside the vehicle
Mode 4
Speed display works and the miles count is reduced to 40%.
Interval count: stop 50 sec, count 20 seconds, repeat. 40 % is a guide value. The driving environment determines the count. Works independently of software updates for all vehicles until 2023. The indicator: Turn light x4 flashes only inside the vehicle
Mode 5
The kilometres are counted at 100%
The module is deactivated, the speedometer and the odometer work as usual.
BMW Z4 G29 Mileage Blocker tool always maintains the last applied settings. Hence, you don’t have to change the settings before starting a car next time.
The device can be activated or deactivated, either while in motion (only for certain vehicles) or when stationary.
This device is designed only for off-road use and dyno testing and not for fraudulent purposes i.e use on the public road
